Niagara 3000 Delivers Power, Protection, Performance
Power management is a hot topic in audio. Niagara 3000 loves the attention.
Analog Audio Interconnect Cable
Often, the choice between terminating your speaker cables with spade lugs or banana plugs will come down to personal preference. However, the EU-compliant isolated binding posts used on some power amplifiers often makes it difficult if not impossible to tighten spade lugs with high torque or pressure. In these applications, the AudioQuest banana connector is the superior choice, and may be the only choice.
AudioQuest has conducted a fairly extensive survey of contemporary amplifier manufacturers to determine whether spades or bananas will be most appropriate for a given brand and model of amplifier. Please contact us, provide the brand and model of the amplifier, and we’ll respond with the optimal connector type.
Here we typically recommend the U-Spade or banana connector. However, even though there is less weight and pressure on this side of the cable (particularly for BiWire sets), it is nevertheless important to note the binding post’s design. If a banana connector cannot seat all the way into the binding post, we recommend one of our spade connectors.
Solid Perfect-Surface Copper (PSC) Conductors
Since the beginning, AudioQuest has pioneered the use of superior metals, yet even we were surprised by the huge leap in performance attained through the astonishingly smooth and pure surface of Perfect-Surface Copper (PSC). Proprietary metal-processing technology protects the wire's surface at every stage of drawing and fabrication. When high-purity low-oxide copper is kept as soft, pure, and smooth as possible, it becomes a wonderfully low-distortion conductor. In a conventional cable, electrical and magnetic interaction between strands is one of the greatest sources of distortion, often causing a somewhat harsh, dirty sound. Solid conductors are fundamental toward achieving a very clean, natural sound.
Direction-Controlled Conductors
All drawn metal strands or conductors have a non-symmetrical, and therefore directional, grain structure. AudioQuest controls the resulting RF impedance variation so that noise is drained away from where it will cause distortion. The correct direction is determined by listening to every batch of metal conductors used in every AudioQuest audio cable. When applicable, arrows are clearly marked on the connectors to ensure superior sound quality. For most models of AQ cable, the arrows not only indicate the direction that optimizes metal-directionality as part of Noise-Dissipation, but also indicates non-symmetrical attachment of shield and GND in order to optimize full-system performance. A fundamental aspect of AudioQuest's multifaceted Noise-Dissipation technology, Direction-Controlled Conductors ensure induced noise is dissipated and drained properly.
Metal-Layer Noise-Dissipation
It's easy to accomplish 100% shield coverage. Preventing captured radio-frequency interference (RFI) from modulating the equipment's ground reference requires AQ's Noise-Dissipation. Traditional shield systems typically absorb and then drain noise/RF energy to component ground, modulating and distorting the critical "reference" ground plane, which in turn causes a distortion of the signal. Noise-Dissipation "shields the shield," absorbing and reflecting most of this noise/RF energy before it reaches the layer attached to ground.
Hard-Cell Foam Insulation
Hard-Cell Foam (HCF) Insulation ensures critical signal-pair geometry. Any solid material adjacent to a conductor is actually part of an imperfect circuit. Wire insulation and circuit board materials all absorb energy. Some of this energy is stored and then released as distortion. Hard-Cell Foam Insulation is similar to the Foamed-PE used in our more affordable Bridges & Falls cables, and is nitrogen-injected to create air pockets. Because nitrogen (like air) does not absorb energy and therefore does not release any energy from or into the conductor, distortion is reduced. In addition, the stiffness of the material allows the cable's conductors to maintain a stable relationship along the cable's full length, producing a stable impedance character and further minimizing distortion.
Triple-Balanced Geometry
Our Triple-Balanced Geometry uses a separate ground-reference conductor, so the cable's shield is never used as an inferior conductor. Whether prepared with RCA or XLR plugs, the cable's three conductors ensure that the positive and negative signals have equally superior, low-distortion conducting paths.
Cold-Welded, Gold-Plated Terminations
This plug design allows for a connection devoid of solder, which is a common source of distortion. Instead of solder, the process employs a high-pressure technique. Because the ground shells are stamped instead of machined, the metal used can be chosen for low distortion instead of machinability.
Technical Specifications | |
---|---|
Cable Configuration |
2 Single Cables - 1 x Male RCA > 1 x Male RCA
|
Metal |
Solid Perfect-Surface Copper (PSC)
|
Noise Dissipation |
Metal-Layer
|
Geometry |
Triple-Balanced
|
Insulation |
|
Terminations |
|
Signal Type |
|
Cable Length |
0.5 m = 1 ft 7 in
|
Jacket |
Red on Black Braid
|
Weights & Dimensions | |
Sold As |
|
Red River RCA > RCAVanaf $104.98 Details bekijken | Chicago RCA > RCAVanaf $59.98 Details bekijken | Mackenzie RCA > RCAVanaf $149.98 Details bekijken | Yukon RCA > RCAVanaf $215.00 Details bekijken | |
---|---|---|---|---|
Cable Configuration |
2 Single Cables - 1 x Male RCA > 1 x Male RCA
|
2 Single Cables - 1 x Male RCA > 1 x Male RCA
|
2 Single Cables - 1 x Male RCA > 1 x Male RCA
|
2 Single Cables - 1 x Male RCA > 1 x Male RCA
|
Metal |
Solid Perfect-Surface Copper (PSC)
|
Solid Long-Grain Copper (LGC)
|
ZERO: Solid Perfect-Surface Copper+ (PSC+) / BASS: Solid Perfect-Surface Copper+ (PSC+)
|
ZERO: Solid Perfect-Surface Copper+ (PSC+) / BASS: Solid Perfect-Surface Copper+ (PSC+)
|
Noise Dissipation |
Metal-Layer
|
Metal-Layer
|
Carbon Mesh-Network
|
Carbon Mesh-Network
|
Geometry |
Triple-Balanced
|
Double-Balanced
|
Triple-Balanced
|
Triple-Balanced
|
Insulation |
|
|
|
|
Terminations |
|
|
|
|
Signal Type |
|
|
|
|
Sold As |
|
|
|
|